Screenshots
Shots from the current build: not mock-ups, not a designer's impression. Every number in them came out of the software. Click any image to see it full size, or read the tutorial for three whole jobs a step at a time.
The way in
Forty-seven shapes, grouped the way a shop thinks about them rather than alphabetically. Quick Design is one part straight to a DXF with no job around it; New Job adds the parts list, materials and costing when you need to quote.
Anything you draw in Quick Design can be turned into a job later without redrawing it.
The development
An 800 to 350 cone, 600 high, in 3 mm plate. The diameters were typed as inside diameters, so the pattern develops on the middle of the material and the girth comes out 9.4 mm longer than the bare numbers would give. Seam laps are drawn in green, on their own DXF layer.
Before you cut
The same cone as a model, from iso, the top, the front or the side. The seam is green and any fixing holes are blue, so you can see where the joint lands before the plate is on the machine — which is the cheapest time to notice it is in the wrong place. Tap a dimension on the model to change it.
Checking
Eight kinds of measurement, and the picks snap to ends, centres, midpoints, quadrants and intersections. Along curve runs the tape around the arc rather than straight across it — between the same two points on this cone that is the difference between 2050 mm and 2543 mm. Every measurement stays on the drawing and comes out on the marking-out sheet.
The detail most software gets lazy about
A 300 duct in 1.6 mm. If 300 is the inside diameter, the blank is not π×300. It is π×301.6, because the material rolls about its middle — 5 mm of girth, which is a 5 mm gap or a 5 mm overlap at the seam. Set it per part; the software says in plain words what it did.
The general transition
Round 500 at the bottom, an 800 × 400 rectangle on top leaning 30°. Each end can be round, a rectangle with a corner radius, a flat oval, a polygon or your own corner points, and either can lean and turn. The straight sides come out as flat triangles, the corners as cones, and the red lines are where the rolling starts.
Cladding
NPS 4 steel pipe, 50 mm of rockwool, and the 20 mm of girth this shop adds because rockwool is never quite its nominal thickness. The drawing is end on and to scale: pipe wall, insulation, the allowance, the cladding, and the lap at the seam. Use for this field puts the answer into the fitting.
Bigger than the plate
A 1500 lobster-back on 3000 × 1500 plate. Each gore is 4.7 metres round, so one click on Split to fit the sheet made every gore two plates — the fewest that fit, laps included. Plate k of every gore covers the same arc, so the joints meet.
New in the current beta
An 1800 ellipsoidal head in eight petals round a 450 crown cap, every seam turned through 30° from the cap out to the rim. The petal is developed so the girth closes at every parallel and its two welded edges come out the same length; the form says how far the seam turns, its angle at the rim and how much the press has to take up.
On paper
Behind the marking-out sheet comes a page of offsets from a baseline: strike the baseline, square up at each station, mark the heights, join the marks. It works for every shape, because it is read off the finished blank. A triangulated part also gets its true lengths, step by step from the seam.
The same cone as above. The true-length table for the general transition is here.
From the building model
One floor of a hospital's supply ductwork from the consultant's IFC model. Each duct and fitting is listed with the shape it becomes and how its numbers were read, straights are cut to the stock length, and the diffusers and damper are set aside as bought in. Nothing reaches the job until Add to job.
Model space add-on · new
A supply main with a side-branch tee, a transition and a radius bend, a return run alongside and a toilet exhaust riser, each in its system's colour. Every label is the part number the job gives that fitting, and the problems panel says every joint fits and nothing clashes. More on Model space.
Model space add-on · new
The ground floor and two typical floors above it, on a site datum, with grid lines A to C and 1 to 2. The supply has been copied up both floors and shows faint; the return is dimensioned 300 clear of the supply and locked, so widening the supply moves the return with it.
Model space add-on · new
Print layout draws a floor for the installers at a stated scale: every fitting in plan in its system's colour, the job's part numbers in bubbles, each straight's size and underside height, the grid, the held dimension and every hanger. A schedule follows on the next sheet, and the same layout goes out as a DXF.
Takeoff add-on
The scale read off the title block, the trunk and branches measured and labelled with the sizes written beside them, and one diffuser boxed and named SD-1: all fourteen on the sheet found and counted. Revision B can be laid over A to see what changed.
Plate
The bottom cone of a hot water tank in 8 mm plate, 1600 down to 150, split into two to fit a 3000 × 1500 plate. The roll lines run across the blank and a 60 mm pre-bend flat sits past each seam for the edge the rolls cannot reach; the seams carry a 30° single V.
Vessel calculations add-on
A 200 NB inlet in a 1600 shell with a 440 pad, checked by area replacement against the design spec's numbers. Every area is listed, the verdict says it needs the sign-off of whoever is responsible for the design, and Print calculation sheet writes it out for signing.
Every feature is listed by the work it is for, and the tutorial walks an insulation job, an HVAC job and a plate job from start to finish in 41 of the program's own screens. Nesting I want through real jobs on real tables before I call it finished; if cutting is your end of the job, there is a tester list.
30-day trial
That is the only test worth doing. Develop something you have cut before, check the girth against your own numbers, and see whether it agrees.